Related Links
The effects of recycling on the physical and mechanical properties of wood plastitc composite made with high density polyethylene | ||
| تحقیقات علوم چوب و کاغذ ایران | ||
| Article 9, Volume 32, Issue 3 - Serial Number 60, September 2017, Pages 402-410 PDF (374.62 K) | ||
| Document Type: Research Paper | ||
| DOI: 10.22092/ijwpr.2017.107141.1356 | ||
| Authors | ||
| Mohammad Zafari sarmori1; saeid reza Farokhpayam* 2; Ehsan Sanei3; mohammad shamsian4 | ||
| 1Graduate student, paper and wood science and technology department, University of zabol, zabol, Iran | ||
| 2Assistant professor, paper and wood science and technology department, University of Zabol, zabol, Iran | ||
| 3Faculty member, M.Sc, paper and wood science and technology department, University of zabol, zabol, Iran | ||
| 4Associate professor, paper and wood science and technology department, University of zabol, zabol, Iran | ||
| Abstract | ||
| Although many studies have been done about the application of waste materials such as used plastics but returning of wood plastic products (Regrind) to the production cycle was rarely reported. In this work, the effect of once and twice regrind on the functional properties of WPC made from high density polyethylene (HDPE) has been studied. The specimens were fabricated with powder raw materials and by the flat press under laboratory conditions. HDEP and poplar wood flour were mixed with a weight ratio of 50-50 percent. The estimation of regrind process, physical and mechanical properties of boards were measured after each regrinding and also to evaluate of regrinding on filler particle size and the interface between the polymer and wood flour some Scanning Electron Microscopy (SEM) were prepared. The results of this research showed that regrinding of WPC leads to a decrease in mechanical properties including bending strength, flexural modulus, tensile strength and tensile modulus and on the other hand regrinding process leads to improved physical properties including water absorption and thickness swelling after hours. SEM photographs showed that during the process of regrinding, filler particle size is reduced while matrix surrounding the filler particles better. | ||
| Keywords | ||
| Regrind; wood plastitc composite; PHYSICAL AND MECHANICAL PROPERTIES; matrix; filler | ||
| References | ||
|
-Beg, M.D.H. and Pickering, K.L., 2008. Reprocessing of wood fibre reinforced polypropylene composites. Composites, Part A 39: 1091–1100. -Chaharmahali, M., Kazemi Najafi, S. and Tajvidi, M., 2006. The Effect of Producing Method on the Mechanical Properties of Wood Plastic Composites Made From Particleboard Wastes. Iranian Journal Of Wood and Paper Science Research, Vol. 21 No.)1) -Ghahri, S., Kazemi-Najafi, S., Mohebby, B. and Tajvidi, M., 2012. Impact strength improvement of wood flour–recycled polypropylene composites. Journal of Applied Polymer Science, 124: 1074-1080. -John, J., Balatinecz, M. and Sain, M., 2009. The Influence of Recycling on the Properties of wood Fiber–plastic composites. Polymer Science & Technology General, 135(1): 167-163. -Kamdem, D.P., Jiang, H.Cui.W., Freed, J. and Matuana L.M., 2004. Properties of wood plastic composites made of recycled HDPE and wood flour from CCA-treated wood removed from service. Department of Forestry, Michigan State University, 35: 347-355. -Kazemi Najafi, S., Mostafazadeh-Marznaaki, M., Chaharmahali, M. and Tajvidi, M., 2009. Effect of thermomehcanical degradation of polypropylene on mechanical properties of woodpolypropylene composites, Journal of Composite Material, 43: 2543-2554. -Mignealt, S., Koubaa, A., Erchiqui, F., Chaala, A., Englund, K. and Wolcott, M., 2008. Effects of processing method and fiber size on the structire and properties of wood-composites. Composites, Part A 40: 80–85. -Miranda Leao, R., Maria da Luz, S., Araújo, J.A. and Christoforo, A.L., 2015. The Recycling of Sugarcane Fiber/Polypropylene Composites, Materials Research, 18(4): 690-697. -Nourbakhsh, A., 2013. The utilization of two recycled polymers and bagasse fiber in wood plastic nano / clay composites production, Iranian Journal of Wood and Paper Science Research, Vol. 28 No. (3). -Nawadon, P., Sirijutararana, C. and Jakkid, S,. 2011. Recycling of wood plastic composite prepared form poly(vinyl chloride) and wood flour. Construction and Building Materials, 28(1): 557-560. -Pillin, I., Montrelay, N., Bourmaud, A. and Grohens, G., 2007. Effect of thermo-mechanical cycles on the physico-chemical properties of poly (lactic acid). Polymer Degradation and Stability, 93: 321-328. -Prachayawarakorn, J. and Yaembunying, N., 2005. Effect of recycling on properties of rice husk-filled-polypropylene. Songklanakarin J. Sci. Technol., 27(2): 343-352. -Ramiah, M.V., 1970. Thermogravimetric and differential thermal analysis of cellulose, hemicellulose, and lignin. J. Appl. Polym. Sci.14, 1323–1337. -Shahi, P., Behravesh, A.H., Daryabari, S.Y. and Lotfi, M., 2012. Experimental Investigation on Reprocessing of Extruded Wood Flour/HDPE Composites. POLYMER COMPOSITES. 754-763. -Shojaei, A., Yousefian, H. and Saharkhiz, S., 2006. Performance characterization of composite materials based on recycled high-density polyethylene and ground tire rubber reinforced with short glass fibers for structural applications. J Apple polym Sci, 104:1-8. -Tajvidi, M. and Takemura, A., 2011. Effects of Reprocessing on the Hygroscopic Behavior of Natural Fiber High-Density Polyethylene Composites. Journal of Applied Polymer Science, Vol. 122, 1258–1267. -Wechsler, A. and Hiziroglu Salim., 2006. Some of the properies of wood-plastic composites, Building and Environment, Vol. 42, No. 5, pp. 2637-2644. -Wolcott, M.P. and Englund, K., 1994. A technology review of wood-plastic composites. 33rd international particleboard/ Composite material symposium Booklet, A. | ||
|
Statistics Article View: 675 PDF Download: 445 |
||
Journal management system. designed by sinaweb