Related Links
Effect of the presence of tobacco stalk wastes mixed with industrial wood particle on the dimensional stability and mechanical properties of particleboard | ||
| تحقیقات علوم چوب و کاغذ ایران | ||
| Article 10, Volume 33, Issue 4 - Serial Number 65, February 2019, Pages 564-578 PDF (877.79 K) | ||
| Document Type: Research Paper | ||
| DOI: 10.22092/ijwpr.2019.123298.1494 | ||
| Authors | ||
| Laya jamali rad* 1; saeed Narooei2 | ||
| 1Assistant Professor, Department of Wood and Paper Science and Engineering, Faculty of Agriculture and Natural Resources,GonbadKavous University, Gonbad, I.R. Iran | ||
| 2Department of Wood and Paper Science and Engineering, Faculty of Agriculture and Natural Resources,Gonbad Kavous University | ||
| Abstract | ||
| The purpose of this study was to investigate the possibility of using tobacco stalk and industrial wood particles in particleboard industry as a waste material that is not consumed and discarded and has a low price, followed by a reduction in production costs from the way of choosing this raw material was of low value. For this purpose, the particles of tobacco stalk and industrial wood particles with different ratios of 0:100, 30:70 and 60:40, using the amount of adhesive used 12% and 14% (based on the dry weight of the wood chips) and the press time of 5 minutes for the construction of the board was considered. Physical and mechanical properties including thickness swelling after 2 and 24 hours immersion in water and bending strength (MOR), modulus of elasticity (MOE) and internal bonding (IB) were measured and all data were statistically analyzed. According to the results of this study, the increase in tobacco stalk particles resulted in increased thickness swelling after 2 and 24 hours immersion in water and reduced bending strength, modulus of elasticity and internal bonding, but all boards had a European standard (EN). Increasing the amount of resin also had a significant effect on all the properties of the boards and improved the properties. In a general conclusion and by comparing the properties of the boards produced with the European standard (EN), showed that using 60% tobacco stalk and 12% urea formaldehyde resin can be produced particleboard with the desired properties. This is a positive result of using tobacco stalk as a type of agricultural residue and, consequently, the prevention of environmental pollution caused by the burning of these compounds. | ||
| Keywords | ||
| Tobacco stalk waste; Urea formaldehyde resin; Thickness swelling; Internal bonding; Bending strength | ||
| References | ||
|
-Alma, M.H., Kalaycıo˘glub, H., Bektas, I. and Tutus, A., 2005. Properties of cotton carpel-based particleboards.Industrial Crops and Products, 22(2):141-149. -Akgül, M., Güler, C. and Ҫöpür, Y., 2010. Certain physical and mechanical properties of medium density fiberboards manufactured from blends of corn (Zea mays indurataSturt.) stalks and pine (Pinusnigra) wood. Turkish Journal of Agriculture and Forestry, 34:197-206. -Alvarez, C., Rojano, B., Almaza, O., Rojas, OJ. andGanan., 2011. P. Self-bonding boards from plantain fiber bundles after enzymatic treatment: adhesion improvement of lignocellulosic products by enzymatic pre-treatment. Journal Polymer Environmental,19:182-188. -Bektas, I., Güler, C., Kalaycioglu, H., Mengeloglu, F. andNacar M., 2005. Themanufacture of particleboards using sunflower stalks (Helianthus annuus L.) and poplar wood (Populus alba L.). Journal of Composite Materials, 39:467-73. -Cheng, E., Sun, X. and Karr, G.S., 2004. Adhesive properties of modified soybean flourin wheat straw particleboard. Composites Part A: Applied Science and Manufacturing, 35(3):297-302. -Copur, Y., Guler, C., Tas_cıog˘lu, C., Tozluog˘lu, A., 2008. Incorporation of hazelnut shell and husk in MDF production.Bioresource Technology, 99:7402-7406. -Ergun, G., Birol, U. and Beyhan, K., 2009. Chemicalcomposition of toma(Solanumlycopersicum) stalkand suitability in the particleboardproduction, Journalof Environmental Biology, 30(5):731-734. -Fathy, L., Faezipour, M.,andBahmani, M., 2010. Effect of UF and MUFresins on the practical properties of particleboard produced from rice strawand aspen particles. Iranian Journal of Wood and Paper ScienceResearch, 25(2):321-331. -Han, G., 2001. Development of high-performance Reed and Wheat straw composite Panels, WOOD RESEARCH, 88:19-39. -Iswanto, A.H., Azhar, I., Supryanto, A. and Susilowanti, A., 2014. Effect of resin type. Pressing temperature and time on particleboard properties made from sorghum bagasse. Agriculture, Forestry and Fisheries, 3(2):62-66. -Jung Lin, C., 2008. Manufacturing particleboard panels from betel palm (Areca catechu Linn.), Science Direct, Journal of Materials Processing Technology,197)1–3:(445-448. -JahanLatibari, A.,Golbabaei, F., Tamjidi, A.,Sobhani, B.and Raofkia A., 2013.Investigation on the utilization ofurban wood residues in theproduction of particleboard. Iranian Journal of Wood and Paper Science Research, 28(1):109-122. -MazhariMousavi, S.M., Hosseini, S.Z., Resalati, H., Mahdavi, S. and RasoolyGarmaroody, E., 2013.Papermaking potential of rapeseed straw, a newagricultural-based fiber source.Journal of Cleaner Production, 52:420-424. -Moya, R., Camacho, D., Soto F.R. and Mata-Segreda, J., 2015. Internal bond of particleboards made of three wood species mixture with empty fruit bunch of Elaeisquineensis, leaves of Ananascomosus or tetra park. Journal of agricultural Science, 4(6):241-247. -Ntalos, G.A. and Grigoriou, A.H., 2002. Characterization and utilization of vinepruning as a wood substitute for particleboard production.Industrial Crops and Products, 16 (1):59-68. -Papadopoulos, A.N., Hill, C.A.S., Gkaraveli, A., Ntalos, G.A. and Karastergiou S.P., 2004. Bamboo chips (Bambusa Vulgaris) as an alternative lignocellulosic raw materials for particleboard manufacture. HolzalsRoh-und Werkstoff, 62(1):36-39. -Pirayesh, H., Khazaeian, A. and Tabarsa, T., 2012.The potential for using walnut (Juglansregia L.) shell as a raw material for wood-based particleboard manufacturing. Composites B, 43:3276-80. -Paridah, M.T., Juliana, A.H., El-Skekeil, Y.A., Jawaid, M. and Alothman, O.Y., 2014.Measurement of mechanical and physical properties of particleboard by hybridization of Kenaf with rubber wood particles. Measurement, 56:70–80. -Rangavar, H., Rasam, G., and Aghagolpour, V., 2011. Investigation on the Possibility of Using Canola Stem Residues for Particleboard manufacturing. Journal of Wood and Forest Science and Technology, 18(1):91-104. -Rassam, G., Azadifard, M., Kargarfard, A. and Fazeli, F., 2014. Investigation the possibility of particleboard manufacture using corn stalks. , Iranian Journal of Wood and Paper Science Research, 28(4):609-623. -Sain, M. and Panthapulakkal, S., 2006. Bioprocess preparation of wheat straw fibersand their characterization. Industrial Crops and Products, 23(1):1-8. -Sudin, R. and Swamy, N., 2006. Bamboo and wood fiber cement composites for sustainable infrastructure regeneration. Materials Science, 41(21):6917-6924. -Shakhes, J.A.B., Marandi, M., Zeinaly, F., Saraian, A., and Saghafi, T., 2011. Tobacco Residuals As Promising Lignocellulosic Materials For Pulp And Paper industry. BioResources, 6(4):4481-4493. -Sarki, J., Hassan, S.B., Aigbodion, V.S. and Oghenevweta.J.E., 2011.Potential of using coconut shell particle fillers in eco-composite materials.Journal of Alloys Compound, 509:2381-2385. -Tabarsa, T., Ashori, A. andGholamzadeh, M., 2011. Evaluation of surface roughness andmechanical properties of particleboard panels made from bagasse.Composites: Part B, 42(5):1330-1335. -Usta, M., Kırcı, H. and Eroglu, H., 1990. Soda-Oxygen pulping of corn (Zea mays induratasturt). In: Tappi Pulping Conference: Toronto, Ontario,Canada, Proceeding Book, 1:307-312. -Xiaqun, M., Enzhicheng, A., 2003. Physical properties of medium density wheat straw particleboard using different adhesive. Industrial crop and products,18:47-53. -Zhang, L. and Hu, Y., 2014. Novel lingo cellulosic hybrid particleboard compositesmade from rice straws and coir fibers.Materials and Design, 55:19–26. | ||
|
Statistics Article View: 947 PDF Download: 525 |
||
Journal management system. designed by sinaweb