1جنگلداری-دانشکده منابع طبیعی-دانشگاه گیلان-رشت-ایران
2استادیار، گروه صنایع چوب و کاغذ، دانشگاه فنی و حرفه ای تهران
چکیده
تخته الیاف- گچ کامپوزیتی است که از الیاف بعنوان تقویت کننده در زمینه گچی استفاده شده است. هدف این مقاله بررسی تاثیر مقادیر مختلف الیاف کاغذباطله براستحکام، مقاومت ونحوه شکست تخته الیاف – گچ بوده است. برای این منظور از مقادیر صفر، 5، 10، 15، 20، 25 و35 درصد الیاف کاغذباطله استفاده شده است. نتایج حاصل از اندازه گیری مقاومت خمشی، چسبندگی داخلی و جذب رطوبت درطی یک ماه قرار گرفتن در رطوبت نسبی 100درصد نشان می دهد که افزایش مقدار الیاف تا 20 درصد باعث افزایش خواص مکانیکی شده است. به طورکلی استفاده 20 درصدی از الیاف باعث دو برابر و نیم شدن چسبندگی داخلی و افزایش 50 درصدی مقاومت خمشی درمقایسه با نمونه شاهد شده است. منحنی نیرو- جابجایی گویای این است که افزایش 5 الی 15 درصد الیاف در رفتارشکست تخته الیاف- گچ تغییری ایجاد نمی کند و همانند شاهد حالت ترد و شکننده دارد. درحالی که درمقادیر بیشتر جایگزینی انعطاف پذیری افزایش یافته و شکست حالت نرم پیدا می کند. بنابراین بهترین شرایط از نظراستحکام، مقاومت و انعطاف پذیری در20 درصد جایگزینی زمینه گچی با الیاف کاغذ باطله بدست آمده است.
Investigation of the effect of waste paper fibers on the fracture behavior of fiber-gypsum board
نویسندگان [English]
Javad Torkaman1؛ rouzbeh asadi khansari2
1Forestry-Faculty of Natural Resources , University of Guilan, Iran
2Department of wood industry, Technical and Vocational University (TVU),Tehran,Iran
چکیده [English]
Fibre-gypsum board is a composite, in which fiber used as the reinforcement in the matrix of gypsum. The purpose of this article is to investigate the effect of different amounts of waste paper fibers on the strength, resistance and the fracture behavior of fiber-gypsum board. For this purpose, amounts of zero, 5, 10, 15, 20, 25 and 35 percent of waste paper fibers have been used. The results of measuring bending strength, internal bonding and moisture absorption during one month exposure to 100% relative humidity show that increasing the percentage of fibers up to 20% has increased the mechanical properties. In general, By using twenty percent fibers the bending strength increased fifty percent and the internal bonding became double and half in comparison to the control samples. The load-displacement curve shows that an increase of 5 to 15 percent of fibers does not change the fracture behavior of the fiber-gypsum board and they had brittle fracture same as control samples. While in more substitution values, the flexibility increases and the failure becomes ductile. Therefore, the best conditions in terms of strength, resistance, and flexibility have been obtained in 20% replacement of gypsum with waste paper fibers.