1دانشجوی دکترای دکترای تخصصی، گروه علوم و صنایع چوب و کاغذ، واحد کرج، دانشگاه آزاد اسلامی، کرج، ایران.
2دانشیار، گروه علوم و صنایع چوب و کاغذ، واحد کرج، دانشگاه آزاد اسلامی، کرج، ایران.
3استاد، گروه علوم و صنایع چوب و کاغذ، واحد کرج، دانشگاه آزاد اسلامی، کرج، ایران.
چکیده
از محدودیتهای تشخیص میزان عمر مفید باقیمانده در اجزای سازههای در شرایط مصرف با روشهای صوتی، عدم امکان محاسبه-ی مدولالاستیسیته به دلیل امکان نداشتن خروج قطعه از سازه میباشد. بنابراین اکثر درجهبندیهای در حین مصرف در اجزای سازه-هایی از قبیل بناهای تاریخی براساس سنجش سرعت صوت میباشد. در این تحقیق به محاسبهی دانسیتهی کلی و ناحیهای با روش میزان نفوذ میخ در تراورسهای چوبی به منظور محاسبات مربوط به تشخیص میزان عمر مفید باقیماندهی آنها با تلفیق روشهای موجتنش، ارتعاش طولی آزاد پرداخته شده است. بین مقادیر سرعت صوت کلی و مدولالاستیسیته کلی با نتایج ناحیهای حاصل از این فاکتورها در پنج نقطه مورد آزمون در هر یک از تراورسها تفاوت معنیداری وجود نداشت. همچنین بین دانسیتهی محاسبه شده با روش استاندارد ایزو 13910 و نتایج حاصل از روش میزان نفوذ میخ نیز تفاوت معنیداری وجود نداشت. همبستگی نمایی مطلوبی بین مدولالاستیسیتهی محاسبه شده با روش موج تنش و مقادیر میرایی ارتعاش طولی وجود داشت. نتایج حاکی از آن بود که تلفیق سه روش مذکور کارایی بسیار مطلوبی جهت کلاسهبندی چوب در حین مصرف و بدون خروج از سازه دارد.
Evaluation of the local dynamic modulus of elasticity in wooden tie by the stress wave method
نویسندگان [English]
Ebrahim Khosravi1؛ Amir Lashgari2؛ Mehran Roohnia3؛ Ahmad Jahan latibari3؛ Ajang Tajdini2
1- Ph.D. Student, Department of Wood and Paper Science and Technology, Karaj Branch, Islamic Azad University, Karaj.
2Associate Professor, Department of Wood and Paper Science and Technology, Karaj Branch, Islamic Azad University, Karaj.
3Professor, Department of Wood and Paper Science and Technology, Karaj Branch, Islamic Azad University, Karaj.Iran.
چکیده [English]
From the limitations of detecting the amount of useful life remaining in the components of the structures in the conditions of use with acoustic methods is the impossibility of calculating the modulus of elasticity due to the impossibility of removing the part from the structure. Therefore, most of the classifications during use in the components of structures such as historical buildings are based on measuring the speed of sound. In this research, to calculate the local and global density with the method of pin penetration rate in wooden tie in order to calculate the amount of their remaining useful life by combining stress wave and free longitudinal vibration methods has been studied. There was no significant difference between the values of global sound velocity and global modulus of elasticity with the local results of these factors at the five tested points in each of the wooden tie. Also, there was no significant difference between the density calculated by the ISO 13910 standard method and the results of the pin penetration rate method. There was optimal exponential correlation between modulus of elasticity calculated from stress wave method and damping factor from longitudinal vibration. The results indicated that the combination of the three mentioned methods has a very favorable efficiency for the classification of wood during consumption and without leaving the structure.
کلیدواژهها [English]
wooden tie, stress wave, local modulus of elasticity, density, structure